Woodworking Tips
Below you will find a link to our current Tip and a way to search our past Illustrated tips.

Past Tips:
To view a past tip, make a selection from below and press the enter button.

#278 Jointing Veneers #277 No Room For Wiggle #266 Avoiding unsightly staining and marring during project clamp-up #265 The Robin Hood method of stock storage and rapid sorting #264 Storing workshop air hoses and extension cords without tangling #262 Avoiding unsightly location marks on project components #261 How to cut plastics without melting problems #260 How too much sanding can actually ruin your finish #259 Viewing large project plans sheets without giving up work space #258 Protective Router Bit Storage #257 Take a break for improved results #256 Clean Nail Removal #255 Cutting Accurate Shapes #254 Clampless edge banding #253 Dust free laundry room #252 Flat is where its at #251 Taking the bump and bounce out of your turnings #250 When is more better than less? #249 Important Safety Tip #248 Warp Free Laminates #247 Hand-screw Storage #246 Priming end-grain for strength #245 Getting a grip on large sheet-goods #244 Stop guessing about the appearance of wood stains #243 Strong Wood Selection #242 No-cost metal rulers #241 Protective pads for vise or clamp jaws #240 Small Parts Holder #239 Getting a Grip on Drill Bits #238 Beware of toxic glue #237 Choosing the right hammer #236 Holding your temper #235 Where does it go -- why isn't it there? #234 Sanding into tight spots #233 Making exact duplicates tomorrow #232 Lathe mounted sanding drum #231 Non stick clamp/vise #230 Grip on large sheet goods #229 Parts Box ID #228 Pegboard Solution #227 Avoiding brass screw problems #226 Low cost paint trays #225 Spin proof cabinet knobs #224 On-target toenailing #223 Fat component into skinny groove or dado #222 Miter Clamping Trick #221 Large Diameter Compass #220 To Hold or not to Hold #219 Variable rate disc sanding #218 Substitute for steel dowels #217 Trick for sanding small surfaces #216 Drilling super hard woods #215 Stop chasing benchtop tools #214 Storing green wood #213 Gripping tiny drill bits #212 Stubborn jar lid opener #211 Put a shine on that tape #210 Scuff-sanding sandpaper choices #209 Waste-free brush-cleaning #208 Pipe clamp workbench hold-down #207 Saw Table picture frame clamp #206 Filling cracks with wood #205 Mar-free marking of softwoods #204 Repairing peeled-up veneers #203 Thumbscews in a pinch #202 Beware of nail sizes #201 Straight line cutting of plastics #200 Preventing canned compounds from solidifying #199 Setting mortise depths #198Cutting/shortening bolts #197 Getting every last drop #196 Boring deep, small-diameter holes #195 Strengthening particle board butt joints #194 Preventing a fastener sorting mess #193 Achieving the right speed for shop-made tools #192 Gain better control over sprinkled abrasive powders #191 How to bore straight (perpendicular) holes #190 Maintaining Bench Vise jaw alignment #189 Simple, Inexpensive Tool Holder #188 Keeping Spray Can Nozzle Clean #187 Creating a Stopped Dado #186 Assembling Dovetails Without Breakage #185 Maintaining Squareness When Hand Planing A Board #184 Repairing Checks & Splits #183 Precision Marking #182 Long Clamps From 2"x4"s #181 Fixing Poor-Fitting Joinery #180 All about Router Bits Pt9 #179 All about Router Bits Pt8 #178 All about Router Bits Pt7 #177 All about Router Bits Pt6 #176 All about Router Bits Pt5 #175 All about Router Bits Pt4 #174 All about Router Bits Pt3 #173 All about Router Bits Pt2 #172 All about Router Bits Pt1 #171 Gluing Oily Woods #170 Tips For Using Files & Rasps #169 Understanding Files & Rasps #168 More Woodworking Chisel Basics #167 Woodworking Chisel Basics #166 Quick spillled nail pickup #165 Stowaway shop light is always ready #164 Tightening the fit of dadoes and grooves #163 Eliminating binding when using hollow-ground saw blades #162 Snug fitting moldings #161 Avoiding clamp jaw damage #160 Power Station Tune-Up #159 Thickness Planer Tune-Up #158 Dust Collector Tune-Up #157 Scroll Saw Tune-Up #156 Bandsaw Tune-Up #155 Belt Sander Tune-Up #154 Jointer Tune-Up #153 Strip Sander Tune-Up #152 MARK V Tune-Up Part 3 #151 MARK V Tune-Up Part 2 #150 MARK V Tune-Up Part 1 #149 Removing small dents from furniture #148 Starting Screws in hard-to-reach areas #147 Figuring angle cuts on the Table Saw #146 Using Off-The-Shelf Moldings to Make Box Feet #145 Maximizing the Performance of A New Dust Collector #144 Self-Adjusting Dowels for Trial Assemblies #143 Shop-built Portable Circular Saw Cutting Guide #142 Avoiding problems of small Table Saw cut-offs #141 Cutting Tight Bandsawn curves #140 Sandpaper Pad/Disc Storage #139 Using Brass Screws #138 8 Great Uses For Double Stick Tape #137 Shop-Made Wood Putty #136 Emergency Dowel Fluting #135 Maintaining Measurement Accuracy #134 Forstner Bit Use & Maintenance #133 Coiling Bandsaw Blades #132 Mortise-And-Tenon Facts #131 Rip Fence Alignment Tip #130 Clog-Free Lathe Sanding #129 Reinforcing Mitered Corners #128 All About Nails #127 Understanding Lumber Grades #126 Smoother Bandsaw Scroll Cuts #125 Machinist's Set-Up Blocks #124 Saw Blade Selection #123 Neat Bandsaw Trick #122 Mitre Gauge Storage Jig #121 Table Saw Kickback Guide #120 Make A Classic Shop Stool #119 How to Make A Band Saw Re-saw Jig #118 Jig for Sharpening Jointer Blades #117 Cutting Dovetails on a Band Saw #116 Build A Sandpaper Sizing Jig #115 Make Your Own Cam Clamps #114 Techniques for Face Plate Turning #113 How To Make Cabriole Legs #112 Turning Laminated Bowls #111 What is A Winding Stick #110 How To Sand Outside Curves #109 How To Sand Bevels #108 How To Sand Chamfers #107 How to Sand Stock To A Circle #106 How to Sand Round Corners #105 How To Sand To Exact Width #104 How To Duplicate Short Stock #103 How To Sand To Exact Length #102 How To Sand Crosscuts #101 How To Drill Holes In Glass #100 How To Drill Holes In Metal #99 How To Use A Router For Cutting A Stop Rabbet #98 How to Drill Holes for A Pegged Joint #97 How To Drill Holes For Dowels In Mitered Corners #96 How To Drill Long Holes #95 How To Drill Holes for Doweled Table Top #94 How To Make A Dowel Joint On A Table Leg #93 How To Drill Holes At Compound Angles #92 How To Drill Angular Holes #91 How To Counterbore For Screws #90 How to Drill Holes for Screws In Hardwood #89 How To Drill Pilot Holes in Softwood #88 How To Resaw Lumber #87 How To Cut Saw Kerfs For Bending #86 How To Cut A Cove Molding #85 How To Make A Half Lap Miter Joint #84 N/A #83 N/A #82 How To Make Two Common Joints #81 How to Make Compound Angular Cuts #80 How to Cut Chamfers #79 How to Cut Bevels #78 How to Rip Long Tapers on Flat Boards #77 How to Make A Tapering Jig #76 How to Crosscut Tapers on Flat Boards #75 How to Make Angular Cuts #74 How to Make Tongue & Groove Joint #73 How To Cut Rabbets #72 How to Crosscut Stock to Equal Lengths #71 How to Crosscut Lumber #70 How to Rip Lumber #69 Drilling Equidistant Holes #68 Compound Cuts on Bandsaw #67 Basic Drawer Construction #66 How to Read Wood Grain #65 Making Picture Frames #64 Sharpening Guide Kit #63 Build Lawn/Patio Planter Box #62 Build Lawn/Patio Table #61 Build Lawn/Patio Chair #60 Making Raised Panel Jig #59 Veneering #58 MARK V Cleaning Tips #57 MARK V Maintenance Tips #56 Lathe Turning #55 Table Saw Basic Cuts #54 MARK V Introduction #53 Overarm Pin Router #52 Jig Saw #51 Shopsmith Scroll Saw #50 Shopsmith Jointer #49 Wood Toxicity Table #48 Compound Miter Chart #47 Resawing with N. Engler #46 Finishing Tips - Pt. 6 #45 Finishing Tips - Pt. 5 #44 Finishing Tips - Pt. 4 #43 Finishing Tips - Pt. 3 #42 Finishing Tips - Pt. 2 #41 Finishing Tips - Pt. 1 #40 Glossary of Terms #39 Drying Your Own Lumber #38 Molding #37 Hand Scrapers Use & Care #36 Gluing Up #35 Sanding on a Belt Sander #34 Planing on A Planer #33 Basics of Lathe Turning #32 Everything About Chucks #31 Band Sawing Versatility #30 Lathe Duplicator Tutorial #29 Doing Jointery on Your Table Saw #28 Table Saw Special Operations #27 Everything About Sawing #26 Drill Press #25 Everything About Drilling #24 Shaping #23 Successful Routing #22 Horizontal Boring in Woodworking #21 Choosing A Router Bit #20 Finishing & Finishing Techniques #19 Sharpening Woodworking Tools #18 Not Available #17 Disc Sanding #16 Fences & Shutters #15 Honing #14 Dado Set #13 10 Tips to Store Wood #12 Biscuit Jointer #11 Everything Need to Know About Clamping #10 Mortise & Tenon #9 Dust Collection #8 Belt Sander #7 Strip Sanding #6 Drum Sanding #5 Everything you need to know about sanding #4 Using Molder to make decorative accents & frames #3 Twelve Tips for Choosing and Using Wood Screws #2 Eleven Tips for Making Bread/Cutting Boards #1 Seven Simple Steps to Frame & Raised Panel Construction